[1] Mauro, J. C. et al. Two Centuries of Glass Research: Historical Trends, Current Status, and Grand Challenges for the Future. International Journal of Applied Glass Science 5, 313-327 (2014). doi: 10.1111/ijag.12087
[2] Zirker, J. B. An Acre of Glass: A History and Forecast of the Telescope. (Baltimore: Johns Hopkins University Press, 2005).
[3] Ellis, W. S. Glass: From the First Mirror to Fiber Optics, the Story of the Substance That Change the World. (Harper Collins, New York, 1998).
[4] Molesini, G. Galileo’s telescope and the birth of instrumental optics: a review note. Applied Optics, AO 49, D1-D5 (2010). doi: 10.1364/ao.49.0000d1
[5] Shamloo, A. et al. Impact of compression molding conditions on the thermal and mechanical properties of polyethylene. Journal of Applied Polymer Science 135, 46176 (2018). doi: 10.1002/app.46176
[6] Zhou, J. et al. Stress Relaxation and Refractive Index Change of As2S3 in Compression Molding. International Journal of Applied Glass Science 8, 255-265 (2017). doi: 10.1111/ijag.12244
[7] Málek, J. et al. Crystal Growth Velocity in As2Se3 Supercooled Liquid. Crystal Growth & Design 17, 4990-4999 (2017). doi: 10.1021/acs.cgd.7b01001
[8] Chesworth, A. A. et al. Precision optical components for lidar systems developed for autonomous vehicles. in Proceeding of SPIE 10561, Next-Generation Optical Communication: Components, Sub-Systems, and Systems VII vol. 105610J (SPIE, San Francisco, CA, 2018).
[9] Symmons, A. et al. A practical approach to LWIR wafer-level optics for thermal imaging systems. in Proceeding of SPIE 8704, Infrared Technology and Applications vol. 870425 636–645 (SPIE, Baltimore, MA, 2013).
[10] Atwa, Y. et al. Manufacturing fused silica hemispherical resonators using polymer glass suspension and replication molding. Journal of Micromechanics and Microengineering 34, 085005 (2024). doi: 10.1088/1361-6439/ad5b6a
[11] Nagourney, T. et al. Fabrication of hemispherical fused silica micro-resonator with tailored stiffness and mass distribution. in Proceeding of the 2018 IEEE Micro Electro Mechanical Systems (MEMS) 1000–1003 (IEEE, Belfast, UK, 2018).
[12] Atwa, Y. et al. Fabrication and analysis of printable fused-silica based double paddle oscillators. Sensors and Actuators A: Physical 363, 114783 (2023). doi: 10.1016/j.sna.2023.114783
[13] Kotz, F. et al. Glassomer—Processing Fused Silica Glass Like a Polymer. Advanced Materials 30, 1707100 (2018). doi: 10.1002/adma.201707100
[14] Rapp, B. E. et al. Additive Manufacturing of Glass: From Science to Applications. (Elsevier, 2024).
[15] SMITH, W. Modern Optical Engineering. (McGraw-Hill Education, 2023).
[16] Greis, U. et al. Injection Molding of Plastic Optics. in Optical Surface Technology vol. 0381 69–77 (SPIE-Int Soc Optical Engineering, Garmisch-Partenkirchen, Germany, 1983).
[17] Osaka Gas Chemicals. Polyester (OKP Optical Plastic): for injection molding, raw material of the film. https://www.ogc.co.jp/e/products/fluorene/okp.html.
[18] Steinich, T. et al. Optical design of camera optics for mobile phones. Advanced Optical Technologies 1, 51-58 (2012). doi: 10.1515/aot-2012-0002
[19] Fang, F. Z. et al. Manufacturing and measurement of freeform optics. CIRP Annals 62, 823-846 (2013). doi: 10.1016/j.cirp.2013.05.003
[20] Rolland, J. P. et al. Freeform optics for imaging. Optica, OPTICA 8, 161-176 (2021). doi: 10.1364/OPTICA.413762
[21] Gao, S. H. et al. Design, analysis, and manufacturing of a glass-plastic hybrid minimalist aspheric panoramic annular lens. Optics & Laser Technology 177, 111119 (2024). doi: 10.1016/j.optlastec.2024.111119
[22] Welford, W. T. Aberrations of Optical Systems. (Routledge, New York, 2017). doi: 10.1201/9781315136530.
[23] Forbes, G. W. Shape specification for axially symmetric optical surfaces. Optics Express, OE 15, 5218-5226 (2007). doi: 10.1364/oe.15.005218
[24] Hoeks, T. L. et al. Transparent articles prepared from thermoplastic compositions having low birefringence. (2011).
[25] Wondraczek, L. et al. Advancing the Mechanical Performance of Glasses: Perspectives and Challenges. Advanced Materials 34, 2109029 (2022). doi: 10.1002/adma.202109029
[26] Deegan, J. Glass Molding Makes Aspheric Lenses a Practical Choice. Photonics spectra 41, 72-76 (2007).
[27] Yi, A. Y. Optical Fabrication. in The Optics Encyclopedia (eds. Brown, T. G. et al. ) (Wiley, 2007). doi: 10.1002/9783527600441.oe061.
[28] He, S. et al. Use of Six Plastic Lenses to Design Lens Module with 13 Million Pixels for Application in Cellphone Camera Module. Sensors and Materials 34, 3637 (2022). doi: 10.18494/sam4026
[29] Ansys Canada Ltd. , Designing Cell phone Camera Lenses Part 1: Optics. Knowledgebase https://support.zemax.com/hc/en-us/articles/7686411841043-Designing-Cell-phone-Camera-Lenses-Part-1-Optics (2022).
[30] Edmund Optics Inc. All About Aspheric Lenses. https://www.edmundoptics.com/knowledge-center/application-notes/optics/all-about-aspheric-lenses/.
[31] Wang, H. et al. Two-photon polymerization lithography for imaging optics. International Journal of Extreme Manufacturing 6, 042002 (2024). doi: 10.1088/2631-7990/ad35fe
[32] Milster, T. D. et al. Design aspects of large-aperture MODE lenses. OSA Continuum 4, 171-181 (2021). doi: 10.1364/OSAC.410187
[33] Xia, K. L. et al. Thermal diffusion preparation and rebonding behavior of Ge20Se80-xTex infrared gradient glass. Ceramics International 50, 13318-13326 (2024). doi: 10.1016/j.ceramint.2024.01.244
[34] Brar, N. et al. Precision glass molding technology for the MODE lens telescope. in Proceeding of SPIE 9888, Optical Manufacturing and Testing XIV vol. 12221 95–107 (SPIE, San Diego, CA, 2022).
[35] Brunner, R. Transferring diffractive optics from research to commercial applications: Part I – progress in the patent landscape. Advanced Optical Technologies 2, 351-359 (2013). doi: 10.1515/aot-2013-0055
[36] Zhang, Y. Y. et al. Precision glass molding of diffractive optical elements with high surface quality. Optics Letters, OL 45, 6438-6441 (2020). doi: 10.1364/OL.406195
[37] Prater, K. et al. Precision glass molding of high-resolution diffractive optical elements. in Proceeding of SPIE 12221, Micro-Optics 2016 vol. 9888 163–170 (SPIE, Brussels, Belgium, 2016).
[38] Nakai, T. US Patent: Optical System and Optical Apparatus Having the Same. (2009).
[39] Nakai, T. et al. Research on multi-layer diffractive optical elements and their application to camera lenses. in Diffractive Optics and Micro-Optics DMA2 (OSA, Tucson, Arizona, 2002). doi: 10.1364/DOMO.2002.DMA2.
[40] Levitt, T. A Short Bright Flash: Augustin Fresnel and the Birth of the Modern Lighthouse. (W. W. Norton, New York, 2013).
[41] Yamamoto, H. The innovative components in the field of optics. in (Fraunhofer IPT, Aachen, Germany, 2006).
[42] Milster, T. D. et al. US Patent: A multi-order diffractive Fresnel lens (MOD-DFL) and method for enhancing images that are captured using the MOD-DFL. (2025).
[43] Grunwald, T. et al. Wafer-Level Glass Molding of Chalcogenide Glasses. in (Neuchatel, CH, 2019).
[44] Arnold, S. et al. 52.3: An Improved Polarizing Beamsplitter LCOS Projection Display Based on Wire‐Grid Polarizers. SID Symposium Digest of Technical Papers 32, 1282–1285 (2001).
[45] Khan, S. A. et al. Optical System for Head-Mounted Display. (2021).
[46] Khan, S. A. et al. Optical System for Head-Mounted Display. (2023).
[47] Gollier, J. et al. Pancake lens with large fov. (2018).
[48] Jones, R. A. et al. Rapid optical fabrication with computer-controlled optical surfacing. Optical Engineering 30, 1962-1968 (1991). doi: 10.1117/12.56019
[49] Wang, W. et al. Review of magnetorheological finishing on components with complex surfaces. International Journal of Advanced Manufacturing Technology 131, 3165-3191 (2024). doi: 10.1007/s00170-023-11611-x
[50] Vukobratovich, D. et al. Fundamentals of Optomechanics. (CRC Press, Boca Raton, FL, 2023).
[51] Ansys Zemax OpticStudio | Optical Design and Analysis Software. https://www.ansys.com/products/optics-vr/ansys-zemax-opticstudio.
[52] Forbes, G. W. Robust, efficient computational methods for axially symmetric optical aspheres. Optics Express, OE 18, 19700-19712 (2010). doi: 10.1364/OE.18.019700
[53] Ming, W. Y. et al. A comprehensive review of theory and technology of glass molding process. International Journal of Advanced Manufacturing Technology 107, 2671-2706 (2020). doi: 10.1007/s00170-020-05051-0
[54] Zhou, T. F. et al. Recent advancements in optical microstructure fabrication through glass molding process. Frontiers in Mechanical Engineering 12, 46-65 (2017). doi: 10.1007/s11465-017-0425-2
[55] Zhou, T. F. et al. A review of the techniques for the mold manufacturing of micro/nanostructures for precision glass molding. International Journal of Extreme Manufacturing 3, 042002 (2021). doi: 10.1088/2631-7990/ac1159
[56] Zhang, L. C. et al. Precision glass molding: Toward an optimal fabrication of optical lenses. Frontiers in Mechanical Engineering 12, 3-17 (2017). doi: 10.1007/s11465-017-0408-3
[57] Zhou, T. F. et al. A Review of the Precision Glass Molding of Chalcogenide Glass (ChG) for Infrared Optics. Micromachines 9, 337 (2018). doi: 10.3390/mi9070337
[58] Asgar, Md. A. et al. A Comprehensive Review of Micro/Nano Precision Glass Molding Molds and Their Fabrication Methods. Micromachines 12, 812 (2021). doi: 10.3390/mi12070812
[59] Akhtar, A. et al. Review on thin film coatings for precision glass molding. Surfaces and Interfaces 30, 101903 (2022). doi: 10.1016/j.surfin.2022.101903
[60] Yin, S. H. et al. Review of small aspheric glass lens molding technologies. Frontiers in Mechanical Engineering 12, 66-76 (2017). doi: 10.1007/s11465-017-0417-2
[61] Zhu, T. et al. Advances in hot embossing technology for optical glass micro-nanostructures: A review. Precision Engineering 92, 141-166 (2025). doi: 10.1016/j.precisioneng.2024.11.016
[62] Akhtar, A. et al. Review on thin film coatings for precision glass molding. Surfaces and Interfaces 30, 101903 (2022). doi: 10.1016/j.surfin.2022.101903
[63] Fischbach, K. D. et al. Investigation of the effects of process parameters on the glass-to-mold sticking force during precision glass molding. Surface and Coatings Technology 205, 312-319 (2010). doi: 10.1016/j.surfcoat.2010.06.049
[64] Chao, C. L. et al. Study on the design of precious metal based protective films for glass moulding process. Surface and Coatings Technology 231, 567-572(2013).
[65] Woods, R. O. Clears Glass. Mechanical Engineering 128, 38-41 (2006). doi: 10.1115/1.2006-oct-4
[66] Lawn, B. Fracture of Brittle Solids. (Cambridge: Cambridge University Press, 1993). doi: 10.1017/CBO9780511623127.
[67] Lambropoulos, J. C. From Abrasive Size to Subsurface Damage in Grinding. in Proceeding of the Optical Fabrication and Testing, Quebec City, Canada: Optical Publishing Group (2000) OMA6 (2000). doi: 10.1364/OFT.2000.OMA6.
[68] Lambropoulos, J. C. et al. Loose abrasive lapping hardness of optical glasses and its interpretation. Applied Optics, AO 36, 1501-1516 (1997). doi: 10.1364/ao.36.001501
[69] Angle, M. et al. Method for molding glass lenses. (1974).
[70] Iqbal, W. Identifying the optimum process parameters of precision glass molding for aspherical lenses. (Clemson University, Clemson, 2009).
[71] 170GPMV3 | Nanotech. https://nanotechsys.com/170gpmv3/.
[72] Maschmeyer, R. O. et al. Optical performance of a diffraction-limited molded-glass biaspheric lens. Applied Optics, AO 22, 2413-2415 (1983). doi: 10.1364/ao.22.002413
[73] Sarhadi, A. et al. Thermal modelling of the multi-stage heating system with variable boundary conditions in the wafer based precision glass moulding process. Journal of Materials Processing Technology 212, 1771-1779 (2012). doi: 10.1016/j.jmatprotec.2012.03.025
[74] Shu, Y. Study on Non-isothermal Molding Process of Precision Optical Microstructure Array. (Hunan University, Changsha, China, 2021).
[75] Mauro, J. C. et al. Fictive Temperature and the Glassy State. Journal of the American Ceramic Society 92, 75-86 (2009). doi: 10.1111/j.1551-2916.2008.02851.x
[76] Zanotto, E. D. Do cathedral glasses flow?. American Journal of Physics 66, 392-395(1998).
[77] Williams, M. L. et al. The Temperature Dependence of Relaxation Mechanisms in Amorphous Polymers and Other Glass-forming Liquids. Journal of the American Chemical Society 77, 3701-3707 (1955). doi: 10.1021/ja01619a008
[78] SCHOTT D 263®. https://www.schott.com/en-us/products/d-263-P1000318.
[79] Su, L. J. Experimental and numerical analysis of thermal forming processes for precision optics. (The Ohio State University, Columbus, 2010).
[80] Liu, C. Y. et al. New Linearized Relation for the Universal Viscosity−Temperature Behavior of Polymer Melts. Macromolecules 39, 8867-8869(2006).
[81] Agboka, K. et al. Influence of radiative heat transfer model on the computation of residual stresses in glass tempering process. International Journal of Applied Glass Science 9, 235-251 (2018). doi: 10.1111/ijag.12335
[82] Mathematical Simulation in Glass Technology. (Berlin: Springer, 2002). doi: 10.1007/978-3-642-55966-2.
[83] Sarhadi, A. et al. Evaluation of the viscoelastic behaviour and glass/mould interface friction coefficient in the wafer based precision glass moulding. Journal of Materials Processing Technology 214, 1427-1435 (2014). doi: 10.1016/j.jmatprotec.2014.02.008
[84] Sarhadi, A. et al. Precision Glass Molding: Validation of an FE Model for Thermo-Mechanical Simulation. International Journal of Applied Glass Science 5, 297-312 (2014). doi: 10.1111/ijag.12071
[85] GMP Series. https://www.shibaura-machine.co.jp/en/product/nano/lineup/gmp/.
[86] Huang, W. Y. et al. Atomic Carbide Bonding Leading to Superior Graphene Networks. Advanced Materials 25, 4668-4672 (2013). doi: 10.1002/adma.201301899
[87] Shu, Y. et al. Fabrication of large-scale infrared diffractive lens arrays on chalcogenide glass by means of step-and-repeat hot imprinting and non-isothermal glass molding. International Journal of Advanced Manufacturing Technology 116, 3075-3085 (2021). doi: 10.1007/s00170-021-07716-w
[88] Koren, Y. et al. Real-Time Open Control Architectures and System Performance. CIRP Annals 45, 377-380 (1996). doi: 10.1016/S0007-8506(07)63084-4
[89] Zhang, L. et al. Fabrication of infrared hexagonal microlens array by novel diamond turning method and precision glass molding. Journal of Micromechanics and Microengineering 29, 065004 (2019). doi: 10.1088/1361-6439/ab10ff
[90] Woodbury, K. A. et al. Inverse Heat Conduction: Ill-Posed Problems. (Wiley, Hoboken, NJ, 2023). doi: 10.1002/9781119840220.
[91] Tarantola, A. Inverse Problem Theory and Methods for Model Parameter Estimation. (Society for Industrial and Applied Mathematics, Paris France, 2005). doi: 10.1137/1.9780898717921.
[92] Siedow, N. et al. Direct and Inverse Temperature Reconstruction of Hot Glass. International Journal of Forming Processes 7, 421-430 (2004). doi: 10.3166/ijfp.7.421-430
[93] Wang, L. F. et al. Stress analysis of a large diameter aspheric plastic lens in the variable temperature assisted injection molding process. Applied Optics 63, 1320 (2024). doi: 10.1364/AO.511657
[94] Chen, Y. et al. Numerical Simulation and Experimental Study of Residual Stresses in Compression Molding of Precision Glass Optical Components. Journal of Manufacturing Science and Engineering 130, 051012 (2008). doi: 10.1115/1.2950062
[95] Tao, B. et al. Annealing of Compression Molded Aspherical Glass Lenses. Journal of Manufacturing Science and Engineering 136, 011008 (2013). doi: 10.1115/1.4025395
[96] Liu, G. Modeling Fracture Behavior in Precision Glass Molding. (Apprimus Wissenschaftsverlag, 2018).
[97] Liu, Y. et al. Analysis of lens fracture in precision glass molding with the finite element method. Applied Optics 60, 8022 (2021). doi: 10.1364/AO.436359
[98] Hu, Y. W. et al. Variotherm assisted precision injection molding of plastic optical lenses based on improved cooling stage control model. Scientific Reports 15, 15451 (2025). doi: 10.1038/s41598-025-96659-3
[99] Yan, J. W. et al. Modeling high-temperature glass molding process by coupling heat transfer and viscous deformation analysis. Precision Engineering 33, 150-159 (2009). doi: 10.1016/j.precisioneng.2008.05.005
[100] Jain, A. et al. Numerical Modeling of Viscoelastic Stress Relaxation During Glass Lens Forming Process. Journal of the American Ceramic Society 88, 530-535 (2005). doi: 10.1111/j.1551-2916.2005.00114.x
[101] Ananthasayanam, B. et al. Final Shape of Precision Molded Optics: Part I—Computational Approach, Material Definitions and the Effect of Lens Shape. Journal of Thermal Stresses 35, 550-578 (2012). doi: 10.1080/01495739.2012.674830
[102] Sellier, M. et al. An iterative algorithm for optimal mould design in high-precision compression moulding. Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture 221, 25-33 (2007). doi: 10.1243/09544054JEM606
[103] Vu, A. T. et al. Experimental investigation of contact heat transfer coefficients in nonisothermal glass molding by infrared thermography. Journal of the American Ceramic Society 102, 2116-2134 (2019). doi: 10.1111/jace.16029
[104] Dora Pallicity, T. et al. Numerical Modeling of Cooling Stage of Glass Molding Process Assisted by CFD and Measurement of Residual Birefringence. Journal of the American Ceramic Society 99, 470-483 (2016). doi: 10.1111/jace.14000
[105] Siedow, N. et al. Axisymmetric modeling of the thermal cooling, including radiation, of a circular glass disk. International Journal of Heat and Mass Transfer 89, 414-424 (2015). doi: 10.1016/j.ijheatmasstransfer.2015.04.091
[106] Soules, T. F. et al. Finite-Element Calculation of Stresses in Glass Parts Undergoing Viscous Relaxation. Journal of the American Ceramic Society 70, 90-95 (1987). doi: 10.1111/j.1151-2916.1987.tb04935.x
[107] Viskanta, R. et al. Theoretical Investigation of Heat Transfer in Glass Forming. Journal of the American Ceramic Society 84, 2296-2302 (2001). doi: 10.1111/j.1151-2916.2001.tb01005.x
[108] Yi, A. Y. et al. Compression Molding of Aspherical Glass Lenses–A Combined Experimental and Numerical Analysis. Journal of the American Ceramic Society 88, 579-586 (2005). doi: 10.1111/j.1551-2916.2005.00137.x
[109] Dambon, O. et al. Efficient mold manufacturing for precision glass molding. Journal of Vacuum Science & Technology B 27, 1445-1449 (2009). doi: 10.1116/1.3056171
[110] Maruyama, T. et al. An Analysis of Molded Deformation in Injection-Compression Molded Plastic Lens by Finite Element Method. Kobunshi Ronbunshu 45, 625-632 (1988). doi: 10.1295/koron.45.625
[111] Choi, W. et al. Design and fabrication of tungsten carbide mould with micro patterns imprinted by micro lithography. Journal of Micromechanics and Microengineering 14, 1519-1525 (2004). doi: 10.1088/0960-1317/14/11/012
[112] Katahira, K. ELID grinding characteristics for the machining of optical surface quality for ceramic spherical lens mold. in Proceeding of the Euspen International Topical Conference on Precision Engineering (Aachen, 2003).
[113] Katsuki, M. Grinding technology of small optical element molds. in Optifab 2003: Technical Digest vol. 1031406 19–21 (SPIE, Rochester, NY, USA, 2003).
[114] Karow, H. H. Fabrication Methods for Precision Optics. (Wiley, Hoboken, NJ, 2004).
[115] Home, D. F. Optical Production Technology. (Adam Hilger, London, 1972).
[116] Cemented tungsten carbide: material properties - Matmatch. https://matmatch.com/suppliers/cera-ceratizit/examples/cemented-tungsten-carbide-properties.
[117] Yan, G. P. et al. Ultraprecision grinding of small-aperture concave aspheric mould insert with tilt axis method. Procedia CIRP 71, 505-510 (2018). doi: 10.1016/j.procir.2018.05.010
[118] Suzuki, H. et al. Precision Grinding of Micro Fresnel Lens Molding Die. Journal of the Japan Society for Precision Engineering 65, 1163-1168 (1999).
[119] NASA: Hubble Space Telescope - NASA Science. https://science.nasa.gov/mission/hubble/ (2023).
[120] Son, B. R. et al. Transferability of Diffractive Structure in the Compression Molding of Chalcogenide Glass. Micromachines 14, 273(2023).
[121] Bifano, T. et al. Fixed abrasive grinding of CVD SiC mirrors. Precision Engineering 16, 109-116 (1994). doi: 10.1016/0141-6359(94)90195-3
[122] Zhang, J. G. et al. Investigation of the material removal process in in-situ laser-assisted diamond cutting of reaction-bonded silicon carbide. Journal of the European Ceramic Society 43, 2354-2365 (2023). doi: 10.1016/j.jeurceramsoc.2023.01.011
[123] Hall, C. New mold manufacturing techniques. in Optical Materials and Structures Technologies II vol. 5868 (Bellingham, WA, 2005).
[124] Shahinian, H. et al. Micro Laser Assisted Machining (µ-LAM) of Precision Optics. in Proceeding of the Optical Design and Fabrication 2019 OT1A. 5 (Optica Publishing Group, Washington DC, 2019). doi: 10.1364/OFT.2019.OT1A.5.
[125] Zhang, C. B. et al. Theoretical and experimental investigation of ultrasonic cutting kinematics and its effect on chip formation and surface generation in high-frequency ultrasonic vibration-assisted diamond cutting. Journal of Materials Research and Technology 30, 5662-5676 (2024). doi: 10.1016/j.jmrt.2024.04.266
[126] Zhang, J. G. et al. Improved machinability of single crystal silicon by applying in-situ laser-vibration hybrid assisted diamond cutting. Journal of Materials Processing Technology 326, 118343 (2024). doi: 10.1016/j.jmatprotec.2024.118343
[127] He, P. et al. Graphene-coated Si mold for precision glass optics molding. Optics Letters, OL 38, 2625-2628 (2013). doi: 10.1364/OL.38.002625
[128] He, P. et al. Development of a low cost high precision fabrication process for glass hybrid aspherical diffractive lenses. Journal of Optics 13, 085703 (2011). doi: 10.1088/2040-8978/13/8/085703
[129] Yi, A. Y. et al. Development of a compression molding process for three-dimensional tailored free-form glass optics. Applied Optics, AO 45, 6511-6518 (2006). doi: 10.1364/ao.45.006511
[130] Hossein Shahinian et al. Effect of laser-assisted diamond turning (Micro-LAM) on form and finish of selected IR crystals. in 1–5 (Las Vegas, Nevada).
[131] Moriwaki, T. Machinability of Copper in Ultra-Precision Micro Diamond Cutting. CIRP Annals 38, 115-118 (1989). doi: 10.1016/S0007-8506(07)62664-X
[132] Lucca, D. A. et al. Effect of Tool Edge Geometry on Energy Dissipation in Ultraprecision Machining. CIRP Annals 42, 83-86 (1993). doi: 10.1016/S0007-8506(07)62397-X
[133] Ravindra, D. et al. Ductile mode material removal and high-pressure phase transformation in silicon during micro-laser assisted machining. Precision Engineering 36, 364-367 (2012). doi: 10.1016/j.precisioneng.2011.12.003
[134] Shahinian, H. et al. Ultraprecision laser-assisted diamond machining of single crystal Ge. Precision Engineering 65, 149-155 (2020). doi: 10.1016/j.precisioneng.2020.04.020
[135] Kim, M. J. et al. Experimental study of the diamond turning characteristics of tungsten carbide (Co 0.5%) when using a chamfered diamond bite. Journal of the Korean Physical Society 61, 1390-1394(2012).
[136] Li, Z. J. et al. Ultrasonically Assisted Single Point Diamond Turning of Optical Mold of Tungsten Carbide. Micromachines 9, 77 (2018). doi: 10.3390/mi9020077
[137] He, P. et al. Compression molding of glass freeform optics using diamond machined silicon mold. Manufacturing Letters 2, 17-20 (2014). doi: 10.1016/j.mfglet.2013.12.002
[138] Mukaida, M. et al. Ductile machining of single-crystal silicon for microlens arrays by ultraprecision diamond turning using a slow tool servo. International Journal of Machine Tools and Manufacture 115, 2-14 (2017). doi: 10.1016/j.ijmachtools.2016.11.004
[139] Xie, P. et al. Rapid hot embossing of polymer microstructures using carbide-bonded graphene coating on silicon stampers. Surface and Coatings Technology 258, 174-180 (2014). doi: 10.1016/j.surfcoat.2014.09.034
[140] Li, L. H. et al. Carbide-bonded graphene-based Joule heating for embossing fine microstructures on optical glass. Applied Surface Science 500, 144004 (2020). doi: 10.1016/j.apsusc.2019.144004
[141] Mamatha, T. G. et al. A Comprehensive Review of Ultrasonic Machining: A Tool for Machining Brittle Materials. in Advanced Materials and Manufacturing Processes (CRC Press, Boca Raton, 2021).
[142] Zhang, X. Y. et al. Theoretical analysis of cooling mechanism in high-speed ultrasonic vibration cutting interfaces. International Journal of Thermal Sciences 184, 108033 (2023). doi: 10.1016/j.ijthermalsci.2022.108033
[143] Singh, J. et al. Rotary ultrasonic machining of advance materials: A review. Materials Today: Proceedings (2023) https://doi.org/10.1016/j.matpr.2023.01.159.
[144] Yang, Z. C. et al. Review of ultrasonic vibration-assisted machining in advanced materials. International Journal of Machine Tools and Manufacture 156, 103594 (2020). doi: 10.1016/j.ijmachtools.2020.103594
[145] Liang, X. L. et al. Micro/nano incremental material removal mechanisms in high-frequency ultrasonic vibration-assisted cutting of 316L stainless steel. International Journal of Machine Tools and Manufacture 191, 104064 (2023). doi: 10.1016/j.ijmachtools.2023.104064
[146] Suzuki, H. et al. Development of Ultrasonic Vibration Assisted Polishing Machine for Micro Aspheric Die and Mold. CIRP Annals 55, 385-388 (2006). doi: 10.1016/S0007-8506(07)60441-7
[147] Suzuki, H. et al. Ultraprecision finishing of micro-aspheric surface by ultrasonic two-axis vibration assisted polishing. CIRP Annals 59, 347-350 (2010). doi: 10.1016/j.cirp.2010.03.117
[148] Zhang, C. B. et al. A Theoretical and Experimental Investigation of High-Frequency Ultrasonic Vibration-Assisted Sculpturing of Optical Microstructures. Applied Sciences 12, 10937 (2022). doi: 10.3390/app122110937
[149] Zhang, X. Q. et al. Suppression of diamond tool wear in machining of tungsten carbide by combining ultrasonic vibration and electrochemical processing. Ceramics International 44, 4142-4153 (2018). doi: 10.1016/j.ceramint.2017.11.215
[150] Cao, J. G. et al. Material removal behavior in ultrasonic-assisted scratching of SiC ceramics with a single diamond tool. International Journal of Machine Tools and Manufacture 79, 49-61 (2014). doi: 10.1016/j.ijmachtools.2014.02.002
[151] Tsuchida, T. et al. Surface conditioning of zirconia ceramic by enhanced ultrasonic vibration-assisted burnishing. Production Engineering 18, 353-366 (2024). doi: 10.1007/s11740-023-01242-2
[152] Liu, X. M. et al. Self-tuned ultrasonic elliptical vibration cutting for high-efficient machining of micro-optics arrays on brittle materials. Precision Engineering 72, 370-381 (2021). doi: 10.1016/j.precisioneng.2021.05.007
[153] Wang, Q. Y. et al. Investigation of diamond wheel topography in Elliptical Ultrasonic Assisted Grinding (EUAG) of monocrystal sapphire using fractal analysis method. Ultrasonics 84, 87-95 (2018). doi: 10.1016/j.ultras.2017.10.012
[154] Prater, K. et al. Micro-structuring of glassy carbon for precision glass molding of binary diffractive optical elements. Optical Materials Express, OME 6, 3407-3416 (2016). doi: 10.1364/OME.6.003407
[155] Klocke, F. et al. Analysis of wear of fused silica moulding using glassy carbon moulds. Production Engineering 10, 367-374 (2016). doi: 10.1007/s11740-016-0681-8
[156] Grunwald, T. et al. Influence of Glassy Carbon Surface Finishing on Its Wear Behavior during Precision Glass Moulding of Fused Silica. Materials 12, 692 (2019). doi: 10.3390/ma12050692
[157] Jurkiewicz, K. et al. Evolution of glassy carbon under heat treatment: correlation structure–mechanical properties. Journal of Materials Science & Technology 53, 3509-3523 (2018). doi: 10.1007/s10853-017-1753-7
[158] Harris †, P. J. F. Fullerene-related structure of commercial glassy carbons. Philosophical Magazine 84, 3159-3167 (2004). doi: 10.1080/14786430410001720363
[159] Chen, T. T. et al. Fabrication of Anti-reflective Structure Array on Chalcogenide Glass by Compression Molding with PDMS Mold. Optical Engineering 62, 045104 (2023). doi: 10.1117/1.oe.62.4.045104
[160] Zhu, Z. C. et al. Antireflective structured surface of chalcogenide glass fabricated using glass to glass molding. Ceramics International 49, 28216-28223 (2023). doi: 10.1016/j.ceramint.2023.06.076
[161] Xiong, H. et al. Chalcogenide microlens arrays fabricated using hot embossing with soft PDMS stamps. Journal of Non-Crystalline Solids 521, 119542 (2019). doi: 10.1016/j.jnoncrysol.2019.119542
[162] Liu, Y. et al. Polymeric microlens array fabricated with PDMS mold-based hot embossing. Journal of Micromechanics and Microengineering 24, 095028 (2014). doi: 10.1088/0960-1317/24/9/095028
[163] Johnston, I. D. et al. Mechanical characterization of bulk Sylgard 184 for microfluidics and microengineering. Journal of Micromechanics and Microengineering 24, 035017 (2014). doi: 10.1088/0960-1317/24/3/035017
[164] Shu, Y. et al. Fabrication of Fresnel lens arrays by a rapid non-isothermal imprinting process. Applied Optics 60, 351-357 (2021). doi: 10.1364/AO.412763
[165] Liu, X. H. Sol Gel Glass Micro and Metasurface Fabrication. in (Sendai, Japan, 2024).
[166] Yan, M. F. et al. Efficient fabrication of large-scale chalcogenide glass microlens arrays via precision molding method. Ceramics International 50, 49194-49199 (2024). doi: 10.1016/j.ceramint.2024.09.261
[167] Su, L. J. et al. Investigation of the effect of coefficient of thermal expansion on prediction of refractive index of thermally formed glass lenses using FEM simulation. Journal of Non-Crystalline Solids 357, 3006-3012 (2011). doi: 10.1016/j.jnoncrysol.2011.04.005
[168] L-BSL7 - Ohara Corp. https://oharacorp.com/glass/l-bsl7/.
[169] Morse, D. L. et al. Welcome to the Glass Age. International Journal of Applied Glass Science 7, 409-412 (2016). doi: 10.1111/ijag.12242
[170] Scherer, G. W. Relaxation in Glass and Composites. (Krieger Pub Co, 1992).
[171] Elliot, S. R. Physics of Amorphous Materials. vol. 20 (Longman Group Ltd, London, 1984).
[172] Gupta, P. K. Non-crystalline solids: glasses and amorphous solids. Journal of Non-Crystalline Solids 195, 158-164 (1996). doi: 10.1016/0022-3093(95)00502-1
[173] Ashby, M. F. et al. Engineering Materials 1: An Introduction to Properties, Applications and Design. (Elsevier, Amsterdam, 2012).
[174] Rekhson, S. Models of relaxation in glass. Journal of Non-Crystalline Solids 95–96, 131–147 (1987).
[175] Kaur, G. et al. A review of bioactive glasses: Their structure, properties, fabrication and apatite formation. Journal of Biomedical Materials Research Part A 102, 254-274 (2014). doi: 10.1002/jbm.a.34690
[176] Su, L. J. et al. Refractive index variation in compression molding of precision glass optical components. Applied Optics, AO 47, 1662-1667 (2008). doi: 10.1364/ao.47.001662
[177] Jain, A. Experimental study and numerical analysis of compression molding process for manufacturing precision aspherical glass lenses. (The Ohio State University, Columbus, 2006).
[178] Gong, F. et al. Precision replication and quality analysis of the molded glass cylindrical lens array. Optics Express 33, 12780 (2025). doi: 10.1364/OE.554939
[179] Gardon, R. et al. Stress and Volume Relaxation in Annealing Flat Glass. Journal of the American Ceramic Society 53, 380-385 (1970). doi: 10.1111/j.1151-2916.1970.tb12137.x
[180] Zhao, W. et al. Refractive index and dispersion variation in precision optical glass molding by computed tomography. Applied Optics, AO 48, 3588-3595 (2009). doi: 10.1364/ao.48.003588
[181] Narayanaswamy, O. S. A Model of Structural Relaxation in Glass. Journal of the American Ceramic Society 54, 491-498 (1971). doi: 10.1111/j.1151-2916.1971.tb12186.x
[182] Ritland, H. N. Relation Between Refractive Index and Density of a Glass at Constant Temperature. Journal of the American Ceramic Society 38, 86-88 (1955). doi: 10.1111/j.1151-2916.1955.tb14581.x
[183] Kakiuchida, H. et al. Refractive Index, Density and Polarizability of Silica Glass with Various Fictive Temperatures. Japanese Journal of Applied Physics 43, L743 (2004). doi: 10.1143/JJAP.43.L743
[184] Zhang, Y. et al. Pre-Compensation of Mold in Precision Glass Molding Based on Mathematical Analysis. Micromachines (Basel) 11, E1069 (2020). doi: 10.3390/mi11121069
[185] Zhang, L. et al. Investigation of index change in compression molding of As40Se50S10 chalcogenide glass. Applied Optics, AO 57, 4245-4252 (2018). doi: 10.1364/ao.57.004245
[186] Shelby, J. E. Introduction to Glass Science and Technology. (Royal Society of Chemistry, Cambridge, 2005).
[187] Tao, B. et al. Numerical analysis of residual stresses reconstruction for axisymmetric glass components. in Proceeding ofSPIE 10616, 2017 International Conference on Optical Instruments and Technology: Optical Systems and Modern Optoelectronic Instruments (eds. Dong, L. et al. ) 36 (SPIE, Beijing, China, 2018). doi: 10.1117/12.2295007.
[188] Tao, B. et al. Quantitatively measurement and analysis of residual stresses in molded aspherical glass lenses. International Journal of Advanced Manufacturing Technology 74, 1167-1174 (2014). doi: 10.1007/s00170-014-6058-2
[189] Fu, H. et al. Prediction model of residual stress during precision glass molding of optical lenses. Applied Optics, AO 61, 1194-1202 (2022). doi: 10.1364/AO.448010
[190] Liu, W. D. et al. Thermoforming mechanism of precision glass moulding. Applied Optics, AO 54, 6841-6849 (2015). doi: 10.1364/ao.54.006841
[191] Zhou, J. et al. Quality dependence study on dimensions for plano-concave molded glass lenses. International Journal of Applied Glass Science 8, 266-275 (2017). doi: 10.1111/ijag.12270
[192] Gardon, R. CHAPTER 5 - Thermal Tempering of Glass. in Glass Science and Technology (eds. Uhlmann, D. R. et al. ) vol. 5 145–216 (Elsevier, 1980).
[193] Klocke, F. et al. Development of a flexible and reliable numerical simulation for precision glass molding of complex glass optics. in Proceeding of SPIE, 6th International Symposium on Advanced Optical Manufacturing and Testing Technologies: Advanced Optical Manufacturing Technologies vol. 841603 25–38 (SPIE, Xiamen, China, 2012).
[194] Pallicity, T. D. et al. Birefringence measurement for validation of simulation of precision glass molding process. Journal of the American Ceramic Society 100, 4680-4698 (2017). doi: 10.1111/jace.15010
[195] Swain, D. et al. A Revisit to the Frozen Stress Phenomena in Photoelasticity. Experimental Mechanics 56, 903-917 (2016). doi: 10.1007/s11340-016-0134-5
[196] Aben, H. et al. Photoelastic Tomography with Linear and Non-linear Algorithms. Experimental Mechanics 52, 1179-1193 (2012). doi: 10.1007/s11340-011-9575-z
[197] Wijerathne, M. L. L. et al. Stress field tomography based on 3D photoelasticity. Journal of the Mechanics and Physics of Solids 56, 1065-1085 (2008). doi: 10.1016/b978-008044046-0/50183-4
[198] Narayanamurthy, C. S. et al. Digital holographic photoelasticity. Applied Optics, AO 56, F213-F217 (2017). doi: 10.1364/ao.56.00f213
[199] Aben, H. et al. Application of the Abel inversion in case of a tensor field. Inverse Problems in Science and Engineering 18, 241-249 (2010). doi: 10.1080/17415970903545124
[200] Anton, J. et al. A Discrete Algorithm of Integrated Photoelasticity for Axisymmetric Problems. Experimental Mechanics 48, 613-620 (2008). doi: 10.1007/s11340-008-9121-9
[201] Jain, A. et al. Finite element modelling of stress relaxation in glass lens moulding using measured, temperature-dependent elastic modulus and viscosity data of glass. Modelling and Simulation in Materials Science and Engineering 14, 465 (2006). doi: 10.1088/0965-0393/14/3/009
[202] Su, L. J. et al. An integrated solution for mold shape modification in precision glass molding to compensate refractive index change and geometric deviation. Optics and Lasers in Engineering 53, 98-103 (2014). doi: 10.1016/j.optlaseng.2013.08.016
[203] Zhou, X. et al. Quantitative evaluation of refractive index inhomogeneity and its effect on the imaging performance of high-precision injection molded optical lens. Journal of Manufacturing Processes 101, 1605-1615 (2023). doi: 10.1016/j.jmapro.2023.07.039
[204] Yen, P. Y. et al. Multi-Objective Optimization of an Injection Molding Process for an Alvarez Freeform Lens Using an Integrated Optical System and Mold Flow Analyses. Polymers 17, 2453(2025).
[205] Kim, H. J. et al. Molding and Optical Evaluation of Aspheric Glass Lenses for Camera Phone Module. Journal of the Korea Industrial Information Systems Research 12, 124-131(2007).
[206] Gain, A. K. et al. Rapid manufacture of defect-free microlens arrays by precision glass molding. Applied Optics 63, 5159 (2024). doi: 10.1364/AO.526069
[207] Okulov, I. V. et al. Flash Joule heating for ductilization of metallic glasses. Nature Communications 6, 7932 (2015). doi: 10.1038/ncomms8932
[208] Xie, J. et al. Mechanism study on microgroove forming by ultrasonic vibration assisted hot pressing. Precision Engineering 46, 270-277 (2016). doi: 10.1016/j.precisioneng.2016.05.007
[209] Nian, S. C. et al. Novel inductive hot embossing for increasing micromolding efficiency. International Communications in Heat and Mass Transfer 70, 38-46(2016).
[210] Li, J. Z. et al. Study on Filling Capacity of Optical Glass in a Novel Rapid Hot Embossing Process. Applied Sciences 12, 3404 (2022). doi: 10.3390/app12073404
[211] Kimerling, T. E. et al. Rapid hot embossing of polymer microfeatures. Microsystem Technologies 12, 730-735 (2006). doi: 10.1007/s00542-006-0098-y
[212] Cheng, C. et al. Application of graphene–polymer composite heaters in gas-assisted micro hot embossing. RSC Advances 7, 6336-6344 (2017). doi: 10.1039/C6RA27618K
[213] Chang, C. Y. et al. A basic experimental study of ultrasonic assisted hot embossing process for rapid fabrication of microlens arrays. Journal of Micromechanics and Microengineering 25, 025010(2015).
[214] Liu, S. J. et al. Hot embossing precise structure onto plastic plates by ultrasonic vibration. Polymer Engineering & Science 45, 915-925(2005).
[215] Xie, J. Q. et al. Mechanism study on microgroove forming by ultrasonic vibration assisted hot pressing. Precision Engineering 46, 270-277 (2016). doi: 10.1016/j.precisioneng.2016.05.007
[216] Zhou, T. F. et al. Improvement of glass formability in ultrasonic vibration assisted molding process. International Journal of Precision Engineering and Manufacturing 18, 57-62 (2017). doi: 10.1007/s12541-017-0007-6
[217] Roylance, M. et al. Modeling of ultrasonic processing. Journal of Applied Polymer Science 93, 1609-1615 (2004). doi: 10.1002/app.20595
[218] Nguyen, L. P. et al. Modeling the Embossing Stage of the Ultrasonic-Vibration-Assisted Hot Glass Embossing Process. International Journal of Applied Glass Science 6, 172-181 (2015). doi: 10.1111/ijag.12090
[219] Fu, X. X. et al. A Rapid Thermal Nanoimprint Apparatus through Induction Heating of Nickel Mold. Micromachines 10, 334 (2019). doi: 10.3390/mi10050334
[220] Saotome, Y. et al. Characteristic behavior of Pt-based metallic glass under rapid heating and its application to microforming. Materials Science and Engineering: A 375–377, 389-393(2004).
[221] Yun, D. W. et al. Development of roll-to-roll hot embossing system with induction heater for micro fabrication. Review of Scientific Instruments 83, 015108 (2012). doi: 10.1063/1.3675574
[222] Kurita, T. et al. Proposal of laser assisted hot embossing technology for glass. Journal of Materials Processing Technology 254, 248-253 (2018). doi: 10.1016/j.jmatprotec.2017.11.040
[223] Chang, J. H. et al. Development of fluid-based heating and pressing systems for micro hot embossing. Microsystem Technologies 11, 396-403(2005).
[224] Zhang, L. et al. Rapid localized heating of graphene coating on a silicon mold by induction for precision molding of polymer optics. Optics Letters, OL 42, 1369-1372 (2017). doi: 10.1364/OL.42.001369
[225] Li, H. et al. Localized rapid heating process for precision chalcogenide glass molding. Optics and Lasers in Engineering 73, 62-68 (2015). doi: 10.1016/j.optlaseng.2015.04.007
[226] Liu, X. H. et al. Simulation and Measurement of Refractive Index Variation in Localized Rapid Heating Molding for Polymer Optics. Journal of Manufacturing Science and Engineering 140, (2017).
[227] Yang, G. et al. Investigation of the heating behavior of carbide-bonded graphene coated silicon wafer used for hot embossing. Applied Surface Science 435, 130-140 (2018). doi: 10.1016/j.apsusc.2017.11.050
[228] Klocke, F. et al. 3D Process Simulation for Precision Glass Molding of Freeform and Wafer Optics. in Proceeding of the 11th European Society for Precision Engineering and Nanotechnology (EUSPEN International Conference) (Como, Italy, 2011).
[229] Huenten, M. et al. Wafer level glass optics: precision glass molding as an alternative manufacturing approach. in Proceeding of SPIE 7927, Advanced Fabrication Technologies for Micro/Nano Optics and Photonics IV vol. 79270L 94–100 (SPIE, San Francisco, CA, 2011).
[230] Klocke, F. et al. Precision Glass Molding of Wafer Lens Optics. in Proceeding of the 12th Euspen International Conference (Stockholm, Sweden, 2012).
[231] Hünten, M. et al. Wafer Level Glass Molding. Key Engineering Materials 523–524, 1001-1005(2012).
[232] Thanner, C. et al. UV Imprinting Processes for Fabrication of Micro Optical Components. in Proceeding of the 2021 International Semiconductor Conference (CAS) 71–74 (Romania: IEEE 2021, 2021). doi: 10.1109/CAS52836.2021.9604160.
[233] Thanner, C. et al. Step and Repeat Imprint Lithography for Wafer Scale Mastering of Micro-and Nanostructures. in Proceeding of the 2022 International Semiconductor Conference (CAS) 69–72 (Polana Brasov, Romania: IEEE 2022, 2022). doi: 10.1109/CAS56377.2022.9934328.
[234] Yamamoto, Y. et al. Precision grinding of microarray lens molding die with 4-axes controlled microwheel. Science and Technology of Advanced Materials 8, 173-176 (2007). doi: 10.1016/j.stam.2007.02.007
[235] Suzuki, H. et al. Precision cutting of structured ceramic molds with micro PCD milling tool. International Journal of Automation Technology 5, 277-282 (2011). doi: 10.20965/ijat.2011.p0277
[236] Li, H. et al. Micro-optical fabrication by ultraprecision diamond machining and precision molding. Frontiers in Mechanical Engineering 12, 181-192 (2017). doi: 10.1007/s11465-017-0444-z
[237] Zhou, T. F. et al. Fabrication of high aspect-ratio aspheric microlens array based on local spiral diamond milling. Journal of Manufacturing Processes 83, 547-554 (2022). doi: 10.1016/j.jmapro.2022.08.064
[238] Sun, Z. W. et al. Flexible fabrication of micro-optics arrays with high-aspect-ratio by an offset-tool-servo diamond machining system. Optics Express, OE 27, 9631-9646 (2019). doi: 10.1364/OE.27.009631
[239] Zhang, L. et al. Flexible fabrication of Fresnel micro-lens array by off-spindle-axis diamond turning and precision glass molding. Precision Engineering 74, 186-194 (2022). doi: 10.1016/j.precisioneng.2021.11.013
[240] Lan, H. B. et al. Nanoimprint Lithography. in in Lithography, ed Wang, M. R. (Rijeka: IntechOpen, 2010). doi: 10.5772/8189.
[241] Chao, C. L. et al. Investigation of the Interfacial Reaction between Optical Glasses and Various Protective Films and Mold Materials. Defect and Diffusion Forum 297–301, 808–813 (2010).
[242] Gao, P. et al. Fabrication of a Micro-Lens Array Mold by Micro Ball End-Milling and Its Hot Embossing. Micromachines 9, 96 (2018). doi: 10.3390/mi9030096
[243] Kang, W. J. et al. Experimental Studies on Fabricating Lenslet Array with Slow Tool Servo. Micromachines 13, 1564 (2022). doi: 10.3390/mi13101564
[244] Yan, G. P. et al. Off-spindle-axis spiral grinding of aspheric microlens array mold inserts. Optics Express, OE 27, 10873-10889 (2019). doi: 10.1364/OE.27.010873
[245] He, Y. P. et al. Generation of high-saturation two-level iridescent structures by vibration-assisted fly cutting. Materials & Design 193, 108839 (2020). doi: 10.1016/j.matdes.2020.108839
[246] Zhu, Z. W. et al. Large-scale fabrication of micro-lens array by novel end-fly-cutting-servo diamond machining. Optics Express, OE 23, 20593-20604 (2015). doi: 10.1364/OE.23.020593
[247] Scheiding, S. et al. Freeform manufacturing of a microoptical lens array on a steep curved substrate by use of a voice coil fast tool servo. Optics Express, OE 19, 23938-23951 (2011). doi: 10.1364/OE.19.023938
[248] Luo, H. et al. Microwave-enabled rapid volumetric heating of moldable low-dielectric-loss glass. Case Studies in Thermal Engineering 57, 104364 (2024). doi: 10.1016/j.csite.2024.104364
[249] Choi, J. et al. A Study on Numerical Analysis for Determination of Glass Molding Process Conditions for Glass Lenses. KSPE 41, 207-214 (2024).
[250] Xu, H. L. et al. Optimization Methods, Theory and Applications. (Springer New York, Berlin, 2015).
[251] Vu, A. T. et al. Nonisothermal glass molding for the cost-efficient production of precision freeform optics. Optical Engineering, OE 55, 071207 (2016). doi: 10.1117/1.oe.55.7.071207
[252] Kim, S. W. et al. Three-dimensional numerical simulation of injection molding filling of optical lens and multiscale geometry using finite element method. Polymer Engineering & Science 46, 1263-1274(2006).
[253] Simoes, R. et al. Development of a rapid heat cycle injection molding system using infrared radiation and convection heating and influence on morphology and mechanical properties. International Journal of Advanced Manufacturing Technology 130, 283-295 (2024). doi: 10.1007/s00170-023-12683-5
[254] Turnhout, M. V. A systematic analysis of the optical merit function landscape: towards improved optimization methods in optical design. in (2009).
[255] Gleason, B. et al. Using design of experiments to improve precision glass moulding. International Journal of Experimental Design and Process Optimisation 3, 263-275 (2013). doi: 10.1504/ijedpo.2013.055742
[256] Huang, S. Z. et al. Optimization of precision molding process parameters of viscoelastic materials based on BP neural network improved by genetic algorithm. Materials Today Communications 35, 106149 (2023). doi: 10.1016/j.mtcomm.2023.106149
[257] Heymann, H. et al. Machine Learning for Predictive Quality in Optics Production. SSRN Journal 259822475 (2023) https://dx.doi.org/10.2139/ssrn.259822475.
[258] Vu, A. T. et al. A hybrid optimization approach in non-isothermal glass molding. AIP Conference Proceedings 1769, 040006(2016).
[259] Liu, W. D. et al. Numerical optimization platform for precision glass molding by the simplex algorithm. Applied Optics, AO 56, 3245-3250 (2017). doi: 10.1364/ao.56.003245
[260] Wang, F. et al. Numerical Simulation Assisted Curve Compensation in Compression Molding of High Precision Aspherical Glass Lenses. Journal of Manufacturing Science and Engineering 131, 011014 (2009). doi: 10.1115/1.3063652